iPhone
Water resistance is not waterproof. After swimming or rain, eject + dry is reasonable. The official IP rating does not cover liquid damage repairs.
Water Eject — 165 Hz Water Removal Sound
Play a low water removal sound that starts at 165 Hz and glides to 250 Hz, which may help get water out of the speaker grille. It is not a guaranteed repair and is not a substitute for drying a soaked phone.
Updated · 4 sources, checked 7 October 2026
On iPhone, turn the Ring/Silent switch to Ring or the page will stay silent.
- Grille facing down
- Not on the charger
- Volume about half
How long?
Ready · 165 Hz gliding to 250 Hz and back
It may move water sitting in the grille. It is not a guaranteed repair and cannot reach water inside the phone.
How does it sound now?
Short answer
Hold the speaker grille facing down and play the tone for 30 seconds. It starts at 165 Hz and glides to 250 Hz and back, which may push droplets out of the grille. Repeat once if it still gurgles, then let the phone air-dry. Do not charge a wet phone, and skip rice and heat. It cannot remove water inside the phone.
How to use it
- Power off only if fully soaked. If the device was submerged, power down and dry the ports with a lint-free cloth first. Do not charge a wet phone.
- Face the speaker down. Hold the grille toward the floor so droplets can leave. Remove the case and any plugged accessories.
- Choose a duration. 30 s is a first pass. 60 s or 90 s if you still hear gurgling. 30 s × 3 adds short rests between bursts.
- Re-test after it dries. Wait a few minutes, then run Speaker Test. Repeat once if needed. Overnight drying still beats looping the tone.
How the 165 Hz water eject sound works
A low tone — here, 165 Hz — moves the speaker enough that a droplet sitting on or in the grille may break surface tension and fall out if you hold the port down. It is the same idea as the iPhone Water Eject shortcut. It is not magic, and it is not a warranty: the tone targets water in the speaker grille, not water inside the phone.
The tone here starts at 165 Hz and glides slowly up to 250 Hz and back, five seconds each way. Every phone speaker has its own resonance, the frequency where the cone moves most easily, and it is rarely exactly 165 Hz. A slow glide through 165–250 Hz spends a few seconds near each phone’s sweet spot instead of betting on a single frequency. It is a sine wave at a capped level, so it never clips into a harsh square wave.
If the device was fully submerged, power it off, wipe ports, and do not charge it. Air-drying still does more than an extra 90 seconds of tone.
30 s, 60 s, 90 s, and 30 s × 3
Short bursts limit heat and let you check progress. The 30 s × 3 mode adds two-second rests between bursts. Stop if you hear distortion or the speaker sounds worse.
Water eject shortcut for iPhone
iPhone has no built-in water eject; the “Water Eject” many people remember is a third-party Siri Shortcut. You can add this page to the Home Screen and use Safari as the player instead of installing an unvetted shortcut from a random gallery. iPhone Speaker Cleaner covers the iPhone-specific steps, including the earpiece and the liquid-detection alert.
How to get water out of phone speaker grilles
- Unplug and power off if it is soaked.
- Wipe visible liquid; do not insert a pin into the grille.
- Hold the speaker down and play a 30 s 165 Hz clip (it glides to 250 Hz and back).
- Wait. Repeat once if it still gurgles.
- Confirm with Speaker Test. If it was only dusty, use Speaker Cleaner.
Skip rice. It adds dust. Skip high-heat dryers. They warp adhesives.
Water in speakers that are not phones
On Bluetooth speakers and tablets the same tone can help get water out of speaker grilles, but keep the volume lower and let fabric grilles dry in moving air. Two exceptions:
- Laptops — water rarely reaches the speaker without reaching the keyboard and board too. Power off and get it serviced; for a dull laptop speaker that never got wet, use Laptop Speaker Cleaner.
- AirPods and earbuds — do not play a tone into wet earbuds. Dry them first; AirPods Water Eject has Apple’s drying steps and a timer.
If you cannot tell whether the problem is water or dust, Fix My Speaker runs both cycles in one pass.
Common devices
Android
Same process. Some phone makers include a built-in eject tone — you can use either. Keep USB-C ports dry before charging.
AirPods
Do not run a loud tone into a wet charging case. Wipe buds, let them dry open, and only then play a short, quiet test.
Smartwatch / small speakers
A 165 Hz tone can still move a tiny driver. Keep volume lower; these enclosures saturate quickly.
If something sounds wrong
Still muffled after water eject
Give it time. Residual moisture can linger. Avoid rice (dust) and heat. Re-run Speaker Test tomorrow before assuming hardware failure.
I need the iPhone water eject shortcut
No iPhone has a built-in water eject — the one people remember is a third-party Shortcut. This page plays the same kind of low tone in Safari with nothing to install. Add it to your Home Screen for one-tap access.
The phone was in salt water or a drink
The residue matters more than the water, and a tone cannot remove it. Apple and Samsung both say to rinse a water-resistant phone with clean tap water and then dry it. Do not charge it until it is dry.
FAQ
Is this the same as a water removal sound?
Yes — they are two names for the same thing: a low tone that moves the speaker so droplets in the grille can fall out. This one is generated in your browser rather than streamed, so it is not compressed.
What frequency is the water eject sound?
This tool starts at 165 Hz, the low tone most water eject clips use, then glides slowly to 250 Hz and back. The best frequency varies by device, so a slow pass through 165–250 Hz reaches more speakers than one fixed tone.
Is there a water eject shortcut for iPhone?
Some Shortcuts gallery items play a similar tone. You do not need one to use this page — open it in Safari, turn off Silent mode and press Play water eject. Add to Home Screen if you want one-tap access.
How do I get water out of a phone speaker?
Power off if soaked, wipe visible liquid, hold the grille down, play a short low tone, then let it air-dry. Do not use a hair dryer on high heat or pack the phone in rice.
How do I know there is still water in my phone speaker?
Water in a phone speaker sounds muffled or gurgling, and bass often buzzes. Play the same song before and after a cycle: if it clears a little each time, it is water. If it sounds the same after it has dried overnight, look at dust or damage instead.
Will this fix water damage?
No. It may help move water sitting in or on the speaker. It cannot reverse corrosion, logic-board damage, or a swollen battery.